We offer a variety of test leads and probes for your Fluke 179 to ensure you are ready for every application.
Features over molded surfaces and finger-hugging curves for a more comfortable and reliable grip, this test lead extension set is designed to improve steadiness in slippery hands.
Includes the Fluke AC220, Fluke TP220, and Fluke TL224.
Featuring TwistGuard test leads with 2 mm diameter probe tips, along with 4 mm adapters.
Built from WearGuard lead wire and silicone insulation, this test lead has an adjustable tip shroud that retracts and extends from 0.75 to 0.16" when you twist it. Additionally, the patented TwistGuard design allows easy adjustments to reduce or increase tip exposure to comply with new electrical safety requirements.
Ideal for high-energy environments. Additionally, this kit comes equipped with a probe extender and probe light, which allows users to illuminate those hard-to-reach areas.
Comes in a small and rugged design, this probe light kit liberates the users' hands for work. Additionally, it features a bright white LED and fits between the modular test probe and test lead.
Single probe pierces 0.01 to 0.6" (0.25 to 1.5 mm) insulated wire with a small pin allows self-healing of the insulation, and 1000 V, 10 A maximum.
Comes equipped with one pair (red, black) of flat, right angle design for connecting to bus bars, and CAT III 600 V, 5 A rating, CSA listed. Adjustable collar provides two ranges of jaw openings up to 1.81" (30 mm).
Designed to improve steadiness in slippery hands, and is for use with TL222 and TL224 test leads. Rubber over-molded surfaces and finger-hugging curves give a comfortable, reliable grip so you can focus on making an accurate measurement.
Designed to improve steadiness in slippery hands, and is for use with TL222 and TL224 test leads. Rubber over-molded surfaces and finger-hugging curves give a comfortable, reliable grip so you can focus on making an accurate measurement.
Designed to improve steadiness in slippery hands, and is for use with TL222 and TL224 test leads. Rubber over-molded surfaces and finger-hugging curves give a comfortable, reliable grip so you can focus on making an accurate measurement.
Designed to improve steadiness with rubber overmolded surfaces and finger-hugging curves. For use with TL222 and TL224 test leads.
Set of three (red, gray, black) safety designed insulated alligator clips for use with STL 120 Shielded Test Leads and TL75 Test Leads. Features a nickel-plated steel jaw contact material with a standard jaw opening of 5/16" (8 mm), and accepts standard 0.08" (2 mm) pin tip sized test probes.
A high-frequency probe designed to convert a DC voltmeter with an input impedance of 10 MΩ into a high frequency (100 kHz to 500 Mhz) RF voltmeter. Additionally, it's probe's DC output is calibrated to equal the RMS value of sine wave input.
Designed to extend the voltage measuring capability of an AC/DC voltmeter to 6000 V peak AC or DC Overvoltage Category I. The probe provides high accuracy when used with a voltmeter having 10 MΩ input impedance. Intended for low energy applications.
Designed to extend the voltage measuring capability of an AC/DC voltmeter to 40,000 V peak AC or DC Overvoltage Category I. The probe provides high accuracy when used with a voltmeter having 10 MΩ input impedance. Intended for low energy applications.
Designed to extend the voltage measuring capability of an AC/DC voltmeter to 15,000 V peak AC or DC Overvoltage Category I. The probe provides high accuracy when used with a voltmeter having 10 MΩ input impedance. Intended for low energy applications.
We accept these payment methods:
We also accept wire transfers/EFT, cheques and purchase orders on approved credit. Accepted payment methods vary by country.
